Cobra Two Port Liposuction Cannula – Luer Lock

The Cobra Style Two Port Liposuction Cannula with Luer Lock fitting is a blunt-tip aspiration cannula with two side ports, used to remove subcutaneous fat under vacuum during liposuction and body contouring. The Luer lock hub screws onto standard Luer lock syringes and suction tubing, so the connection holds under vacuum instead of pulling off mid-pass. It is listed under Cobra Style Two Port Liposuction Cannulas, part of the Healermed Liposuction Cannulas and Accessories range.

Surgeons also refer to this instrument as a Luer lock Cobra cannula, a two-hole lipo cannula, or a dual port aspiration cannula.

Luer Lock Cobra Two Port Cannula in German Stainless Steel

The Luer lock is the most common connection in aesthetic surgery. A threaded collar screws onto the syringe or tubing set and holds the joint closed under vacuum, where a slip fit can pull apart. In syringe-assisted liposuction that matters, because a disconnection breaks the vacuum and interrupts the pass.

Why Two Ports

Port count is the main lever a surgeon has over how aggressive a cannula behaves. More ports remove fat faster but take it from many points at once, which makes an even result harder to control in a thin or superficial layer. Two ports move less per pass, and that is the point: the surgeon can see the contour change gradually and stop at the right moment instead of overshooting.

Two ports also make the draw predictable. With a single hole the whole vacuum load sits at one opening and the cannula can grab; with many holes the flow splits in ways that vary with how the shaft is angled in the tissue. Two openings on a Cobra style shaft give a balanced draw that behaves the same on each pass, which is what makes feathering and edge blending repeatable rather than lucky.

The distal tip is closed and rounded. It separates the plane by blunt dissection as the cannula advances, pushing vessels and nerves aside rather than dividing them, and the vacuum works through the side ports rather than the end of the shaft.

Key Features

• ✔ Threaded Luer lock hub fits standard Luer lock syringes and suction tubing
• ✔ Two ports for controlled, even fat removal rather than fast bulk clearance
• ✔ Balanced draw that behaves the same on every pass, so feathering is repeatable
• ✔ Closed blunt tip separates the plane without cutting vessels or nerves
• ✔ Deburred port edges for clean passage through fat
• ✔ One-piece German stainless steel shaft, fully reusable
• ✔ Custom diameters, lengths and port configurations available on request

Specifications

Clinical Applications

• Superficial liposuction and contour refinement where control matters more than speed
• Feathering and edge blending at the border of a treated area
• Arm, neck and submental contouring with the shorter, smaller-diameter sizes
• Secondary and revision liposuction, where small corrections are the whole job

Material and Sterilization

The cannula is made from German stainless steel with a passivated surface that resists corrosion and pitting through repeated cleaning cycles. It is reusable and can be steam autoclaved at 134°C. Flush the lumen and both ports with clean water immediately after use and dry fully before autoclaving. Check the port edges under light at each cycle: on an aspiration cannula the edge finish is what decides how cleanly fat parts from tissue, and a nicked or dulled edge changes how the instrument behaves.

How to Choose

Diameter sets how much fat comes out per pass and length sets the reach. For general body contouring of the abdomen, flanks and thighs, the 3.0mm to 4.0mm diameters in 25cm to 35cm are the usual working range. The 2.0mm to 2.5mm range in 15cm to 25cm suits arms, the neck and superficial refinement, which is where a two-port cannula is most often chosen. The 1.0mm to 1.5mm diameters in 5cm to 12cm are for fine facial and submental work. Match the fitting to the syringe, vacuum line or handpiece already in your theater.

Why Buy Direct From the Manufacturer

Manufactured by Healermed Instruments, a surgical instruments manufacturer and exporter based in Sialkot, Pakistan. Factory-direct pricing removes the importer and distributor layer. Production runs under an ISO 13485 and FDA CGMP quality system, with ISO 9001 and CE Mark certification. OEM manufacturing and custom branding are available for distributor and brand-owner orders.

Related Instruments

Other fittings in the same cannula range:

• Cobra Style Two Port Liposuction Cannula – Stainless Steel Luer Lock
• Cobra Style Two Port Liposuction Cannula – Super Luer Lock
• Cobra Style Two Port Liposuction Cannula – Universal Luer Lock
• Cobra Style Two Port Liposuction Cannula – main product page
• Cobra Style Two Port Liposuction Cannulas – all fittings

Frequently Asked Questions

What is a Luer lock two port liposuction cannula used for?

It is used to remove subcutaneous fat under vacuum during liposuction, with a threaded hub that screws onto a standard Luer lock syringe or suction tubing set. Two side ports draw more slowly and evenly than a multi-port cannula, which suits superficial work and refinement.

What is the difference between a two-port and a multi-port liposuction cannula?

A two-port cannula has two openings and removes fat more slowly and more evenly; a multi-port cannula has several and clears volume faster. Two ports suit superficial work, refinement and feathering, where control matters more than speed. Multi-port suits bulk debulking of large areas.

Is this cannula autoclavable?

Yes. The instrument is fully reusable and can be steam autoclaved at 134°C. Flush the lumen and both ports with clean water immediately after use, remove all residue before sterilization, and dry completely. Inspect the port edges each cycle, since edge condition on an aspiration cannula affects how it cuts through fat.

What is the minimum order quantity for bulk orders?

The minimum order quantity is agreed per order rather than set at a fixed number. Send us the sizes, fittings and quantities you need through the wholesale request page and we will confirm the minimum for that specification. This lets a small distributor start with a trial order and a larger importer scale up on the same terms.

Do you provide samples?

Yes. Samples are available on request and the buyer covers the shipping charges. Tell us the diameter and length you want to evaluate and we will confirm what can be sent. Testing a sample first is the fastest way to check port edge finish and hub fit against your own syringes.

Can I order a custom size?

Yes. Custom diameters, working lengths and port configurations are available on request in addition to the standard size grid. Send your specification through the wholesale request page and our production team will confirm what can be produced. Custom branding is also available for distributor and OEM orders.