6 Spiral Port Liposuction Cannulas – 1.0mm to 6.0mm

A 6 spiral port liposuction cannula is a blunt-tip aspiration cannula whose six ports are stepped along the shaft and rotated around it rather than grouped at one point. It is used to remove subcutaneous fat under vacuum during liposuction and body contouring, and is chosen for the debulking stage over large areas where pass count needs to stay manageable. This category is part of the Healermed Liposuction Cannulas and Accessories range and covers 11 hub and handle fittings across 84 diameter and length combinations, supplied worldwide to surgeons, clinics and distributors.

Six Spiral Port Cannulas in German Stainless Steel for Large-Area Contouring

On a large area the limit is not how well the surgeon can shape tissue, it is how many passes the case will take. Every extra pass is time under anaesthesia and more fatigue in the hand that has to keep them even. The six spiral port pattern exists to reduce that count without going back to a hard-edged tunnel.

How the Six Spiral Port Pattern Works

Six ports are stepped along the shaft and rotated around it, each one set further back and turned to a different side than the one before. It is the same spiral principle as the three port version, extended: twice the openings, spread over a longer stretch of shaft and covering more of the circumference.

The result is a wider draw band and a faster one. Each pass takes fat from six points at different depths and angles instead of three, so a given area is cleared in fewer passes and the tunnel it leaves is broader and less sharply defined. Adjacent passes overlap heavily, which is what keeps the transitions soft across a large surface.

The trade against the three port version is control. Six openings remove more per stroke, so there is less margin to stop at exactly the right point. That makes this the cannula for the debulking stage over large areas — abdomen, back, outer thighs — and makes the three port version the better choice once the shape is close and the work moves to blending. Many surgeons carry both and switch as the case progresses.

The distal tip is closed and rounded. It separates the plane by blunt dissection as the cannula advances, pushing vessels and nerves aside rather than dividing them, and the vacuum works through the six spiral ports rather than the end of the shaft.

Choose Your Fitting

All fittings below carry the same 6 spiral port shaft, the same closed blunt tip, and the same size grid. Pick the one that matches the syringe, vacuum line or handpiece already in your theater.

If you want the full range on one page, see the main 6 Spiral Port Liposuction Cannula product page. For finer control on superficial and blending work, see the 3 Spiral Port Liposuction Cannulas.

Sizes in This Category

Clinical Applications

• Debulking large areas — abdomen, back and outer thighs
• High-volume body contouring where pass count needs to stay manageable
• Deep-layer work in larger patients with the 4.0mm to 6.0mm diameters
• Flanks and lower back with the 3.0mm to 3.5mm diameters

How to Choose a Size

Diameter sets how much fat comes out per pass and length sets the reach. The six port pattern is built for area, so the 3.5mm to 5.0mm diameters in 30cm to 35cm are the core working range for abdomen, back and outer thighs. The 3.0mm in 25cm to 30cm suits flanks and smaller body areas. Below 2.5mm the six port pattern has little advantage over the three port version, so for arms, neck and superficial work choose the 3 spiral port cannula instead. Match the fitting to the syringe, vacuum line or handpiece already in your theater.

Material and Sterilization

The cannula is made from German stainless steel with a passivated surface that resists corrosion and pitting through repeated cleaning cycles. It is reusable and can be steam autoclaved at 134°C. Flush the lumen and all six ports with clean water immediately after use and dry fully before autoclaving. Because the ports sit at different points along the shaft, turn the cannula while flushing so water passes through each one, and check every opening under light — with six ports there are more places for residue to sit than on any other pattern in the range.

Why Buy Direct From the Manufacturer

Manufactured by Healermed Instruments, a surgical instruments manufacturer and exporter based in Sialkot, Pakistan. Factory-direct pricing removes the importer and distributor layer. Production runs under an ISO 13485 and FDA CGMP quality system, with ISO 9001 and CE Mark certification. OEM manufacturing and custom branding are available for distributor and brand-owner orders.

Frequently Asked Questions

What is a 6 spiral port liposuction cannula used for?

It is used to remove subcutaneous fat under vacuum during liposuction and body contouring, in the debulking stage over large areas. Six ports stepped along the shaft and rotated give a wide draw band, so a big surface is cleared in fewer passes while adjacent passes still overlap and blend.

What is the difference between a 6 spiral port and a 3 spiral port cannula?

Both use the same spiral principle, with ports stepped along the shaft and rotated. The six port version has twice the openings over a longer stretch, so it clears fat faster across a wider band and suits debulking large areas. The three port version removes more slowly and gives more control, which suits blending and superficial work.

Is this cannula autoclavable?

Yes. The instrument is fully reusable and can be steam autoclaved at 134°C. Flush the lumen and all six ports with clean water immediately after use, turning the cannula so water passes through each one, then dry completely before sterilization. Inspect every opening each cycle, since the pattern depends on all six drawing evenly.

What is the minimum order quantity for bulk orders?

The minimum order quantity is agreed per order rather than set at a fixed number. Send us the sizes, fittings and quantities you need through the wholesale request page and we will confirm the minimum for that specification. This lets a small distributor start with a trial order and a larger importer scale up on the same terms.

Which fitting should I order?

Order the fitting that matches your existing equipment, not the shaft. Luer lock for standard syringes and suction tubing, Toomey hub for 60cc syringes, a power handle for manual use with a dedicated handle, and a MicroAire PAL or Lumsail hub only if you own that handpiece. The cannula itself is identical across all of them.

Do you provide samples?

Yes. Samples are available on request and the buyer covers the shipping charges. Tell us the diameter, length and fitting you want to evaluate and we will confirm what can be sent. Testing a sample before a bulk order is the fastest way to check port edge finish and hub fit against your own equipment.

Can I order a custom size?

Yes. Custom diameters, working lengths and port configurations are available on request in addition to the standard size grid. Send your specification through the wholesale request page and our production team will confirm what can be produced. Custom branding is also available for distributor and OEM orders.