Cobra style two port liposuction cannulas are blunt-tip aspiration cannulas with two side ports, used to remove subcutaneous fat under vacuum during liposuction and body contouring. Two ports rather than many gives a slower, more controlled draw, which is what superficial work, feathering and revision cases need. This category is part of the Healermed Liposuction Cannulas and Accessories range and covers 11 hub and handle fittings across 84 diameter and length combinations, supplied worldwide to surgeons, clinics and distributors.
Category at a Glance
- Instrument type: Two-port liposuction aspiration cannulas, reusable
- Ports: Two side ports on a Cobra style shaft
- Tip: Closed blunt tip
- Diameters: 1.0mm (19G) to 6.0mm (4G)
- Working lengths: 3cm to 35cm
- Fittings in this category: 11 hub and handle types
- Material: German stainless steel
- Sterilization: Steam autoclavable to 134°C
- Manufacturer: Healermed Instruments, Sialkot, Pakistan
Two Port German Stainless Steel Cannulas for Controlled Fat Removal
Liposuction results are not decided by how fast fat comes out. They are decided by whether the surgeon can stop at the right point, and that depends on the instrument giving feedback at a rate the hand can respond to. A high-port cannula clears volume quickly but the contour changes faster than the eye can check it. Everything in this category is built for the part of the case where that trade-off runs the other way.
Why Two Ports
Port count is the main lever a surgeon has over how aggressive a cannula behaves. More ports remove fat faster but take it from many points at once, which makes an even result harder to control in a thin or superficial layer. Two ports move less per pass, and that is the point: the surgeon can see the contour change gradually and stop at the right moment instead of overshooting.
Two ports also make the draw predictable. With a single hole the whole vacuum load sits at one opening and the cannula can grab; with many holes the flow splits in ways that vary with how the shaft is angled in the tissue. Two openings on a Cobra style shaft give a balanced draw that behaves the same on each pass, which is what makes feathering and edge blending repeatable rather than lucky.
The distal tip is closed and rounded. It separates the plane by blunt dissection as the cannula advances, pushing vessels and nerves aside rather than dividing them, and the vacuum works through the side ports rather than the end of the shaft.
Choose Your Fitting
All fittings below carry the same Cobra style two port shaft, the same closed blunt tip, and the same size grid. Pick the one that matches the syringe, vacuum line or handpiece already in your theater.
| Fitting | Connects to |
| Luer Lock | Standard Luer lock syringes and suction tubing |
| Stainless Steel Luer Lock | Same as Luer lock, all-steel hub for heavy autoclave cycles |
| Super Luer Lock | Luer connection with a larger bore, longer thread and heavier hub |
| Threaded Fitting | Threaded reusable handles and tubing connectors |
| Fixed Power Handle | Integrated handle, permanently attached to the shaft |
| Grooved Power Handle | Grooved grip handle for controlled passes |
| Black Power Handle | Black anodized handle, reduced glare under operating lights |
| Toomey Hub, 60cc | 60cc Toomey-tip syringes, available from 2.0mm upward |
| MicroAire PAL Compatible | MicroAire PAL power-assisted handpieces |
| Lumsail Compatible | Lumsail machine handpieces |
| Universal Luer Lock | Luer lock hub built to fit across syringe brands |
If you want the full range on one page, see the main Cobra Style Two Port Liposuction Cannula product page.
Sizes in This Category
| Diameters | 1.0mm (19G), 1.1mm (19G), 1.2mm (18G), 1.4mm (17G), 1.5mm (17G), 1.6mm (16G), 1.8mm (15G), 2.0mm (14G), 2.4mm (13G), 2.5mm (13G), 3.0mm (11G), 3.5mm (10G), 4.0mm (8G), 4.5mm (7G), 5.0mm (6G), 6.0mm (4G) |
| Lengths | 3, 4, 5, 7, 7.5, 8, 9, 10, 12, 14, 15, 20, 25, 30, 35cm (by diameter) |
| Custom sizes | Available on request |
| Compliance | FDA CGMP, ISO 13485, ISO 9001, CE Mark |
Clinical Applications
- Superficial liposuction and contour refinement where control matters more than speed
- Feathering and edge blending at the border of a treated area
- Arm, neck and submental contouring with the shorter, smaller-diameter sizes
- Secondary and revision liposuction, where small corrections are the whole job
How to Choose a Size
Diameter sets how much fat comes out per pass and length sets the reach. For general body contouring of the abdomen, flanks and thighs, the 3.0mm to 4.0mm diameters in 25cm to 35cm are the usual working range. The 2.0mm to 2.5mm range in 15cm to 25cm suits arms, the neck and superficial refinement, which is where a two-port cannula is most often chosen. The 1.0mm to 1.5mm diameters in 5cm to 12cm are for fine facial and submental work. Match the fitting to the syringe, vacuum line or handpiece already in your theater.
Material and Sterilization
The cannula is made from German stainless steel with a passivated surface that resists corrosion and pitting through repeated cleaning cycles. It is reusable and can be steam autoclaved at 134°C. Flush the lumen and both ports with clean water immediately after use and dry fully before autoclaving. Check the port edges under light at each cycle: on an aspiration cannula the edge finish is what decides how cleanly fat parts from tissue, and a nicked or dulled edge changes how the instrument behaves.
Buying for your practice? Order online at factory-direct prices, straight from the manufacturer — no distributor markup.
Distributor, importer, or hospital group? Get bulk pricing, OEM manufacturing, and custom branding on the full cannula range.
Why Buy Direct From the Manufacturer
Manufactured by Healermed Instruments, a surgical instruments manufacturer and exporter based in Sialkot, Pakistan. Factory-direct pricing removes the importer and distributor layer. Production runs under an ISO 13485 and FDA CGMP quality system, with ISO 9001 and CE Mark certification. OEM manufacturing and custom branding are available for distributor and brand-owner orders.
Frequently Asked Questions
What is a Cobra style two port liposuction cannula used for?
It is used to remove subcutaneous fat under vacuum during liposuction and body contouring. Two side ports draw more slowly and more evenly than a multi-port cannula, which suits superficial work, feathering at the edge of a treated area, and revision cases where small corrections are the whole job.
What is the difference between a two-port and a multi-port liposuction cannula?
A two-port cannula has two openings and removes fat more slowly and more evenly; a multi-port cannula has several and clears volume faster. Two ports suit superficial work, refinement and feathering, where control matters more than speed. Multi-port suits bulk debulking of large areas.
Is this cannula autoclavable?
Yes. The instrument is fully reusable and can be steam autoclaved at 134°C. Flush the lumen and both ports with clean water immediately after use, remove all residue before sterilization, and dry completely. Inspect the port edges each cycle, since edge condition on an aspiration cannula affects how it cuts through fat.
What is the minimum order quantity for bulk orders?
The minimum order quantity is agreed per order rather than set at a fixed number. Send us the sizes, fittings and quantities you need through the wholesale request page and we will confirm the minimum for that specification. This lets a small distributor start with a trial order and a larger importer scale up on the same terms.
Which fitting should I order?
Order the fitting that matches your existing equipment, not the shaft. Luer lock for standard syringes and suction tubing, Toomey hub for 60cc syringes, a power handle for manual use with a dedicated handle, and a MicroAire PAL or Lumsail hub only if you own that handpiece. The cannula itself is identical across all of them.
Do you provide samples?
Yes. Samples are available on request and the buyer covers the shipping charges. Tell us the diameter, length and fitting you want to evaluate and we will confirm what can be sent. Testing a sample before a bulk order is the fastest way to check port edge finish and hub fit against your own equipment.
Can I order a custom size?
Yes. Custom diameters, working lengths and port configurations are available on request in addition to the standard size grid. Send your specification through the wholesale request page and our production team will confirm what can be produced. Custom branding is also available for distributor and OEM orders.
