Accelerator Three Port Liposuction Cannula – MicroAire PAL

Liposuction Cannulas and Accessories › Accelerator Three Port Liposuction Cannulas › Accelerator Three Port Liposuction Cannula – MicroAire PAL Compatible

The Accelerator Three Port Liposuction Cannula with MicroAire PAL Compatible fitting is supplied with a hub built for that equipment, carrying the same shaft and tip as every other fitting in the range. It is listed under Accelerator Three Port Liposuction Cannulas, part of the Healermed Liposuction Cannulas and Accessories range.

Surgeons also search for this cannula as an accelerator cannula, a graded port liposuction cannula, a three port accelerator lipo cannula, or a progressive port aspiration cannula.

Accelerator Three Port Liposuction Cannula — MicroAire PAL Compatible

Power-assisted systems change how force reaches the tissue. Instead of the surgeon pushing the instrument through the plane, the handpiece drives a short reciprocating stroke and it advances with far less applied force, which reduces fatigue in fibrous or previously operated tissue.

How the Accelerator Port Pattern Works

Three ports along the shaft, graded rather than identical: the openings step up in size from the leading port back toward the hub. That grading is what the name refers to, and it changes how fat moves through the cannula rather than simply how much comes out.

On a conventional multi-port cannula every opening is the same size, and the port nearest the hub has the shortest, easiest path to the suction line. It draws preferentially, while the leading port, furthest from the vacuum, does least of the work. Grading the ports compensates: the smaller leading opening sits where suction is strongest and the larger trailing opening where it is weakest, so all three draw at a more even rate.

The practical effect is that the whole aperture works rather than mostly the back of it. Fat enters along the full working length instead of piling into the rear port, which keeps the lumen supplied steadily and reduces the surging that happens when one opening dominates and then blocks.

Three ports keeps it controllable. This is a working cannula for the main phase of a case, not a debulking instrument, and the even draw is what makes it predictable pass after pass. The distal tip is closed and rounded, separating the plane by blunt dissection while the vacuum works through the three graded side ports.

Key Features

• ✔ Hub built to fit MicroAire PAL power-assisted handpieces
• ✔ Three ports graded in size so all three draw at a more even rate
• ✔ Smaller leading port where suction is strongest, larger trailing port where it is weakest
• ✔ Fat enters along the full working length rather than piling into the rear opening
• ✔ Steadier draw with less surging than equal-sized ports produce
• ✔ Closed blunt tip separates the plane without cutting vessels or nerves
• ✔ One-piece German stainless steel shaft, fully reusable and autoclavable
• ✔ Custom diameters, lengths and port grading available on request

Specifications

Clinical Applications

• General body contouring through the main working phase of a case
• Abdomen, flanks, back and thighs with the 3.0mm to 4.0mm diameters
• Cases where a steady predictable draw matters more than maximum flow
• Arm, neck and submental work with the 2.0mm to 2.5mm diameters

How to Choose

Order this fitting only if you already own a PAL power-assisted handpiece; the hub will not fit a syringe or a manual handle. Diameter sets how much fat comes out per pass and length sets the reach. For body contouring of the abdomen, flanks, back and thighs, the 3.0mm to 4.0mm diameters in 25cm to 35cm are the usual working range and where the graded pattern is used most. The 2.0mm to 2.5mm range in 15cm to 25cm covers arms, the neck and refinement work. For final shaping a single-hole or short-hole cannula removes far less per pass and is the better choice.

Material and Sterilization

The instrument is made from German stainless steel with a passivated surface that resists corrosion and pitting through repeated cleaning cycles. It is reusable and can be steam autoclaved at 134°C. Clean immediately after use and dry fully before autoclaving. The three ports differ in size, so the smallest one blocks first and is the easiest to overlook. Flush from the hub and confirm water runs from each opening individually, smallest first, and check every edge under light at each cycle, since the grading only works while all three are clear.

Why Buy Direct From the Manufacturer

Manufactured by Healermed Instruments, a surgical instruments manufacturer and exporter based in Sialkot, Pakistan. Factory-direct pricing removes the importer and distributor layer. Production runs under an ISO 13485 and FDA CGMP quality system, with ISO 9001 and CE Mark certification. OEM manufacturing and custom branding are available for distributor and brand-owner orders.

Trademark notice: MicroAire and PAL are trademarks of MicroAire Surgical Instruments LLC. Healermed Instruments is not affiliated with, endorsed by, or sponsored by MicroAire. This instrument is independently manufactured and the compatibility reference is provided for the buyer's guidance only.

Other Fittings for This Cannula

More Liposuction Cannulas and Accessories

Frequently Asked Questions

What is a accelerator three port liposuction cannula used for?

It is used to remove subcutaneous fat under vacuum during liposuction and body contouring. Three graded ports distribute the suction evenly along the working aperture, so fat enters across the full length rather than piling into the opening nearest the hub, which keeps the draw steady pass after pass.

What does the graded port sizing actually change?

On equal-sized ports the opening nearest the hub draws hardest, because its path to the vacuum is shortest, and the leading port does least of the work. Grading the sizes compensates: the small leading port sits where suction is strongest and the larger trailing port where it is weakest, so all three draw at a more even rate.

Is this instrument autoclavable?

Yes. It is fully reusable and can be steam autoclaved at 134°C. Clean immediately after use, remove all residue before sterilization, and dry completely.

Which size should I use?

For body contouring of the abdomen, flanks, back and thighs, 3.0mm to 4.0mm diameters in 25cm to 35cm are the usual range and where this pattern is used most. Arms, neck and refinement work suit 2.0mm to 2.5mm in 15cm to 25cm. For final shaping a single-hole or short-hole cannula is the better choice.

What is the minimum order quantity for bulk orders?

The minimum order quantity is agreed per order rather than set at a fixed number. Send us the sizes, fittings and quantities you need through the wholesale request page and we will confirm the minimum for that specification.

Do you provide samples?

Yes. Samples are available on request and the buyer covers the shipping charges. Send us your handpiece details with the diameter and length you want to evaluate.

Can I order a custom size?

Yes. Custom diameters, working lengths and configurations are available on request in addition to the standard size grid. Send your specification through the wholesale request page and our production team will confirm what can be produced.