Both End Bevel Liposuction Cannula – Stainless Steel Luer Lock

Liposuction Cannulas and Accessories › Multi Port Harvester Both End Bevel Liposuction Cannulas › Multi Port Harvester Both End Bevel Liposuction Cannula – Stainless Steel Luer Lock

The Multi Port Harvester Both End Bevel Liposuction Cannula with Stainless Steel Luer Lock fitting is a multi port harvester with both port ends beveled is a fat harvesting liposuction cannula whose ports carry inclined edges at both ends, guiding tissue into the opening rather than cutting through it. It is listed under Multi Port Harvester Both End Bevel Liposuction Cannulas, part of the Healermed Liposuction Cannulas and Accessories range.

Surgeons also search for these liposuction cannulas as fat harvesting cannulas, fat transfer cannulas, fat grafting cannulas, or beveled port harvester cannulas.

Multi Port Harvester Both End Bevel Liposuction Cannula — Stainless Steel Luer Lock

Hub material decides how long a reusable cannula stays usable. Anodized aluminum hubs are lighter and cheaper, but the anodized layer can fade and the thread can gall after repeated steam cycles. A solid stainless steel hub keeps its thread form and finish far longer, which matters in a center running several liposuction cases a day through the same tray.

What Beveling Both Port Ends Does

This fat harvesting cannula carries multiple ports beveled at both ends rather than sharpened. A bevel is an inclined edge: it meets tissue at an angle and leads it into the port, where a sharpened edge divides it and a plain square edge stops it.

The distinction matters when the fat is being kept. Harvested parcels are going back into the patient, and every edge they pass carries a mechanical cost. A beveled port guides tissue inward along an incline instead of cutting through it, so the same volume is collected with less shearing at the opening. That is the reason to choose bevels over sharpened edges: not speed, but how the parcels are treated on the way in.

Beveling both ends keeps that behaviour in both directions. The forward stroke and the return both lead tissue in rather than presenting a square wall, so the draw stays smooth through the whole reciprocating cycle and the cannula does not stall against a band as it comes back.

The trade is throughput. A bevel does not divide fibrous strands, so a dense donor site takes more passes than it would with a sharpened harvester, and the surgeon feels the cannula working rather than cutting. Where the donor site is fatty and even, that costs little. Where it is fibrous, the sharpened specifications will collect the same volume faster. The distal tip is closed and rounded and does not cut.

Key Features

• ✔ Solid stainless steel Luer lock hub — no anodized coating to wear off
• ✔ Ports beveled at both ends guide tissue inward rather than cutting through it
• ✔ Less shearing at the opening for the same collected volume
• ✔ Bevels on both ends keep the draw smooth through the whole reciprocating cycle
• ✔ Closed blunt tip — no cutting surface anywhere on the instrument
• ✔ One-piece German stainless steel shaft, fully reusable and autoclavable
• ✔ Custom diameters, lengths and bevel angles available on request

Specifications

Clinical Applications

• Fat harvesting for facial, breast and gluteal fat transfer
• Even, fatty donor sites where gentleness matters more than speed
• Abdomen, flanks and thighs as donor areas with the 3.0mm to 4.0mm diameters
• Syringe harvesting with the Toomey hub fitting

Material and Sterilization

The cannula is made from German stainless steel with a passivated surface that resists corrosion and pitting through repeated cleaning cycles. It is reusable and can be steam autoclaved at 134°C. Flush the lumen and the opening with clean water immediately after use and dry fully before autoclaving. A bevel is a ground profile, so inspect the incline on both ends of every port under light at each cycle. Once a bevel is flattened or nicked it stops guiding tissue and starts dragging it, which removes the only advantage this specification has over a sharpened harvester.

How to Choose

Diameter sets how much comes out per pass and length sets the reach. For harvesting from the abdomen, flanks and thighs, the 3.0mm to 4.0mm diameters in 25cm to 35cm are the usual working range. The 2.5mm to 3.0mm range in 20cm to 30cm suits smaller donor sites and facial grafting volumes. If the donor site is fibrous, the one-end-sharp or both-end-sharp versions will collect the same volume in fewer passes. Match the fitting to the syringe, vacuum line or handpiece already in your theater.

Why Buy Direct From the Manufacturer

Manufactured by Healermed Instruments, a surgical instruments manufacturer and exporter based in Sialkot, Pakistan. Factory-direct pricing removes the importer and distributor layer. Production runs under an ISO 13485 and FDA CGMP quality system, with ISO 9001 and CE Mark certification. OEM manufacturing and custom branding are available for distributor and brand-owner orders.

Choosing Between the Three Harvester Edge Types

Healermed makes this multiport harvesting cannula in three port-edge specifications. They share the same shaft, the same port layout and the same size grid; only the edges differ, and that difference sets where each one sits between harvest speed and how gently each parcel is separated.

How a Liposuction Cannula Harvests Fat

Harvesting is a function of the cannula, not of the machine behind it. The pump or syringe supplies negative pressure, but what actually happens to the fat is decided at the openings in the shaft, and that is why one harvesting cannula collects a usable graft faster or more gently than another.

The sequence at each port is the same every time. The surgeon advances the cannula through the subcutaneous layer; tissue is drawn against an opening by the vacuum; the edge of that opening separates a parcel of fat from the surrounding tissue; and the parcel travels down the lumen to the syringe or canister. Repeat that a few hundred times across a donor site and you have a graft.

Three things about the cannula decide how that sequence goes. Port size sets how large each parcel is, which matters because the parcel has to pass through the lumen and then through whatever the graft is injected with. Port count sets how many parcels are separated per pass, which is throughput. Edge geometry — sharpened, part-sharpened or beveled — sets how the parcel is separated: divided cleanly, divided in one direction only, or guided in along an incline.

That last one is the choice most surgeons think hardest about, because harvested fat is going back into the patient. Every edge a parcel passes applies mechanical force to it. A cutting edge separates tissue quickly; an inclined edge leads it in with less shearing but takes longer through fibrous strands. Neither is correct in the abstract — the right answer depends on the donor site and on how much volume has to be collected before the case moves on.

Diameter and length are the remaining variables. A wider cannula moves more fat per pass but needs a larger access port and a deeper plane; a longer shaft covers more of the donor area from a single entry. Aspirated fat is thick, so the hub matters too: a narrow Luer taper will throttle a cannula that the shaft itself could keep supplied, which is why Toomey and Super Luer fittings are common on harvesting instruments.

Choose Your Fitting

Every fitting below carries the same multi port harvester both end bevel shaft, the same closed blunt tip and the same size grid. Pick the one that matches the syringe, vacuum line or handpiece already in your theater.

More Liposuction Cannulas and Accessories

Healermed manufactures the full range of cannulas for liposuction, from single hole finishing cannulas to high-flow debulking patterns, in 84 diameter and length combinations.

Frequently Asked Questions

What is a multi port harvester both end bevel liposuction cannula used for?

It is used to collect subcutaneous fat under vacuum for grafting and fat transfer. Ports beveled at both ends guide tissue into the opening along an incline rather than cutting through it, so parcels are collected with less shearing at the port on both the forward and return stroke.

What is the difference between beveled and sharpened harvesting ports?

A sharpened port divides tissue with a cutting edge, which is faster and works through fibrous strands. A beveled port meets tissue at an incline and guides it into the opening instead, so the same volume is collected with less shearing at the edge. Bevels are gentler; sharpened edges are quicker.

Is this cannula autoclavable?

Yes. The instrument is fully reusable and can be steam autoclaved at 134°C. Flush the lumen and the opening with clean water immediately after use, remove all residue before sterilization, and dry completely. Inspect the opening edge under light at every cycle, since edge condition decides how the cannula behaves in tissue.

Which size should I use?

For harvesting from the abdomen, flanks and thighs, 3.0mm to 4.0mm diameters in 25cm to 35cm are the usual range. Use 2.5mm to 3.0mm in 20cm to 30cm for smaller donor sites and facial grafting volumes. On a fibrous donor site the sharpened versions will collect the same volume in fewer passes.

What is the minimum order quantity for bulk orders?

The minimum order quantity is agreed per order rather than set at a fixed number. Send us the sizes, fittings and quantities you need through the wholesale request page and we will confirm the minimum for that specification. This lets a small distributor start with a trial order and a larger importer scale up on the same terms.

Do you provide samples?

Yes. Samples are available on request and the buyer covers the shipping charges. Tell us the diameter and length you want to evaluate and we will confirm what can be sent. A sample also lets you run the steel hub through your own sterilization protocol before a bulk order.

Can I order a custom size?

Yes. Custom diameters, working lengths and opening dimensions are available on request in addition to the standard size grid. Send your specification through the wholesale request page and our production team will confirm what can be produced. Custom branding is also available for distributor and OEM orders.