Fat Aspiration Liposuction Cannula – MicroAire PAL Compatible

Liposuction Cannulas and Accessories › Long Hole Fat Aspiration Tip Liposuction Cannulas › Long Hole Fat Aspiration Tip Liposuction Cannula – MicroAire PAL Compatible

The Long Hole Fat Aspiration Tip Liposuction Cannula with MicroAire PAL Compatible fitting is a long hole fat aspiration tip liposuction cannula is a blunt-tip liposuction cannula with one long aspiration opening at the working tip, used to remove and harvest subcutaneous fat under vacuum during liposuction, body contouring and fat transfer. The long aperture keeps a steady column of tissue moving instead of drawing in surges, which suits high-volume removal and fat harvesting. It is listed under Long Hole Fat Aspiration Tip Liposuction Cannulas, part of the Healermed Liposuction Cannulas and Accessories range.

Surgeons also refer to these liposuction cannulas as fat aspiration cannulas, fat harvesting cannulas, long aperture lipo cannulas, or high-flow fat transfer cannulas.

Long Hole Fat Aspiration Tip Liposuction Cannula — MicroAire PAL Compatible

Power-assisted liposuction changes how force reaches the tissue. Instead of the surgeon pushing the cannula through the plane, the handpiece drives a short, fast reciprocating stroke and the cannula advances with far less applied force. In fibrous or previously operated tissue this reduces both surgeon fatigue and the effort needed for a controlled pass.

How the Long Aspiration Opening Works

This liposuction cannula carries a single long opening, cut along the shaft at the working tip and sized for throughput rather than for shaping. It is the highest-flow single-opening cannula in the Healermed range.

Flow is the whole design goal. Aspirated fat is thick, and on a cannula with small ports it moves in surges as each opening clears and blocks again. A long aperture keeps a continuous column of tissue entering the lumen, so the draw is steady instead of intermittent. For a surgeon that means fewer stalls mid-pass and less time spent clearing the line.

Steady flow matters twice over when the fat is being kept. In fat harvesting for grafting, tissue that is drawn through a narrow opening in surges is worked harder than tissue that enters a wide aperture in a smooth column. A long opening lets the same volume through at lower local force, which is why this pattern is the one reached for when the aspirate is going back into the patient.

The trade is control, and it should be stated plainly. A long aperture removes a lot per pass, so it belongs in the deep and mid layers and in areas with volume to spare. It is not a finishing cannula: once the shape is close, change to a short-hole or single-hole instrument. The tip is closed and rounded, separating the plane by blunt dissection while the vacuum works through the long side opening rather than the end of the shaft.

Key Features

• ✔ Hub built to fit MicroAire PAL power-assisted handpieces
• ✔ Long aspiration opening gives the highest flow of any single-opening liposuction cannula in the range
• ✔ Steady continuous draw instead of the surging typical of small ports
• ✔ Lower local force on tissue at the same volume, which suits fat harvesting for grafting
• ✔ One opening only, so the surgeon always knows where the fat is leaving
• ✔ Closed blunt tip separates the plane without cutting vessels or nerves
• ✔ One-piece German stainless steel shaft, fully reusable and autoclavable
• ✔ Custom diameters, lengths and aperture dimensions available on request

Specifications

Clinical Applications

• High-volume fat removal from the abdomen, back and thighs
• Fat harvesting for grafting and fat transfer procedures
• Deep and mid-layer liposuction where volume is available
• Syringe-assisted harvesting with the Toomey hub fitting

Material and Sterilization

The cannula is made from German stainless steel with a passivated surface that resists corrosion and pitting through repeated cleaning cycles. It is reusable and can be steam autoclaved at 134°C. Flush the lumen and the opening with clean water immediately after use and dry fully before autoclaving. A long aperture is quick to inspect but its edges do all the work, so run a light along the full length of the opening at each cycle and check for any nick or dulled section. Flush the lumen from the hub end until the water runs clear, since a long opening holds more residue than a small port.

How to Choose

Order this fitting only if you already own a PAL power-assisted handpiece; the hub will not fit a syringe or a manual handle. Diameter sets how much fat comes out per pass and length sets the reach. This liposuction cannula is built for throughput, so the 3.0mm to 4.5mm diameters in 25cm to 35cm are the core working range for high-volume removal and fat harvesting. The 2.5mm to 3.0mm range in 20cm to 30cm suits smaller harvest sites and flanks. For superficial work and final shaping, change to a short-hole or single-hole cannula, which removes far less per pass. Match the fitting to the syringe, vacuum line or handpiece already in your theater.

Why Buy Direct From the Manufacturer

Manufactured by Healermed Instruments, a surgical instruments manufacturer and exporter based in Sialkot, Pakistan. Factory-direct pricing removes the importer and distributor layer. Production runs under an ISO 13485 and FDA CGMP quality system, with ISO 9001 and CE Mark certification. OEM manufacturing and custom branding are available for distributor and brand-owner orders.

Trademark notice: MicroAire and PAL are trademarks of MicroAire Surgical Instruments LLC. Healermed Instruments is not affiliated with, endorsed by, or sponsored by MicroAire. This cannula is an independently manufactured instrument and the compatibility reference is provided for the buyer's guidance only.

Choose Your Fitting

Every fitting below carries the same long hole fat aspiration tip shaft, the same closed blunt tip and the same size grid. Pick the one that matches the syringe, vacuum line or handpiece already in your theater.

More Liposuction Cannulas and Accessories

Healermed manufactures the full range of cannulas for liposuction, from single hole finishing cannulas to high-flow debulking patterns, in 84 diameter and length combinations.

Frequently Asked Questions

What is a long hole fat aspiration tip liposuction cannula used for?

It is used to remove and harvest subcutaneous fat under vacuum during liposuction, body contouring and fat transfer. The long aspiration opening at the tip keeps a steady column of tissue moving into the lumen rather than drawing in surges, which gives high flow for volume removal and lower local force when the fat is being kept for grafting.

What is the difference between a long hole aspiration cannula and a multi-port cannula?

A multi-port cannula spreads the draw across several small openings, which clears an area evenly but moves fat in surges as each port blocks and clears. A long aperture keeps one continuous column of tissue entering the lumen, so flow is steadier and higher, which suits high-volume removal and fat harvesting.

Is this cannula autoclavable?

Yes. The instrument is fully reusable and can be steam autoclaved at 134°C. Flush the lumen and the opening with clean water immediately after use, remove all residue before sterilization, and dry completely. Inspect the opening edge under light at every cycle, since edge condition decides how the cannula behaves in tissue.

Which size should I use?

The 3.0mm to 4.5mm diameters in 25cm to 35cm are the core working range for high-volume removal and fat harvesting. Use 2.5mm to 3.0mm in 20cm to 30cm for smaller harvest sites and flanks. For superficial work and final shaping, change to a short-hole or single-hole liposuction cannula, since a long aperture removes far more per pass.

What is the minimum order quantity for bulk orders?

The minimum order quantity is agreed per order rather than set at a fixed number. Send us the sizes, fittings and quantities you need through the wholesale request page and we will confirm the minimum for that specification. This lets a small distributor start with a trial order and a larger importer scale up on the same terms.

Do you provide samples?

Yes. Samples are available on request and the buyer covers the shipping charges. Send us your handpiece details with the diameter and length you want to evaluate. Testing a sample in your own handpiece before a bulk order is strongly recommended for any powered fitting.

Can I order a custom size?

Yes. Custom diameters, working lengths and opening dimensions are available on request in addition to the standard size grid. Send your specification through the wholesale request page and our production team will confirm what can be produced. Custom branding is also available for distributor and OEM orders.