Beveled Hole On Top Liposuction Cannula – Lumsail Compatible

Liposuction Cannulas and Accessories › Beveled Hole On Top Liposuction Cannulas › Beveled Hole On Top Liposuction Cannula – Lumsail Compatible

The Beveled Hole On Top Liposuction Cannula with Lumsail Compatible fitting is a beveled hole on top liposuction cannula is a blunt-tip aspiration cannula with a single angled opening on the upper surface of the shaft, used to remove subcutaneous fat under vacuum during liposuction and body contouring. The inclined edge leads tissue into the aperture as the cannula advances instead of meeting it square, which makes the instrument smoother through fibrous tissue. It is listed under Beveled Hole On Top Liposuction Cannulas, part of the Healermed Liposuction Cannulas and Accessories range.

Surgeons also refer to these instruments as beveled port cannulas, angled opening lipo cannulas, top bevel aspiration cannulas, or bevel window liposuction cannulas.

Beveled Hole On Top Liposuction Cannula — Lumsail Compatible

Equipment-specific hubs exist because handpiece manufacturers do not share a common fitting. A cannula that fits one machine will not seat in another, and forcing or adapting a fitting introduces play at exactly the point that carries mechanical load and holds the vacuum seal. Ordering the correct hub for your machine is the only safe route.

Why the Opening Is Beveled and On Top

A beveled opening is cut at an angle rather than square to the shaft. Instead of a wall of metal meeting the tissue at ninety degrees, the leading edge is inclined, so tissue is led into the aperture as the cannula advances rather than meeting a step.

That angle changes how the cannula engages. A square-cut opening catches fibrous strands and holds them until vacuum pulls them through; a beveled edge draws them in progressively. In practice the instrument feels smoother in dense tissue and needs less force to keep moving, because it is not stopping and restarting against every band it meets.

Placing the bevel on top makes it a superficial instrument. With the opening facing the skin, the surgeon treats the layer they can see and feel, and the inclined edge means that layer is worked gradually rather than in bites. Turn the shaft over and the same cannula addresses the deep layer, though the bevel is designed with the upward orientation in mind.

The angle is also the part that wears. A bevel is a shaped edge, and if it is dulled or flattened the cannula stops leading tissue in and starts pushing it aside, which is the behaviour the design exists to avoid. The distal tip is closed and rounded, separating the plane by blunt dissection while the vacuum works through the beveled opening rather than the end of the shaft.

Key Features

• ✔ Hub machined to fit Lumsail machine handpieces
• ✔ Beveled edge leads tissue into the aperture instead of meeting it square
• ✔ Smoother progress through fibrous tissue with less applied force
• ✔ Top-facing opening puts removal in the layer the surgeon can see and feel
• ✔ Rotate the shaft to work the deep layer with the same instrument
• ✔ Closed blunt tip separates the plane without cutting vessels or nerves
• ✔ One-piece German stainless steel shaft, fully reusable
• ✔ Custom diameters, lengths and bevel angles available on request

Specifications

Clinical Applications

• Superficial liposuction in tissue with fibrous content
• Contour refinement where the cannula must keep moving evenly
• Abdomen, flanks and thighs with the 3.0mm to 4.0mm diameters
• Arm, neck and submental work with the 2.0mm to 2.5mm diameters

Material and Sterilization

The cannula is made from German stainless steel with a passivated surface that resists corrosion and pitting through repeated cleaning cycles. It is reusable and can be steam autoclaved at 134°C. Flush the lumen and the opening with clean water immediately after use and dry fully before autoclaving. The bevel is the working part of this cannula, so inspect the angled edge under light at every cycle: once it is dulled or flattened the opening stops leading tissue in and starts pushing it aside, which is the opposite of what the design is for.

How to Choose

Order this fitting only if your handpiece takes it, and send us your machine details before placing a large order. Diameter sets how much fat comes out per pass and length sets the reach. For body contouring of the abdomen, flanks and thighs, the 3.0mm to 4.0mm diameters in 25cm to 35cm are the usual working range. The 2.0mm to 2.5mm range in 15cm to 25cm covers arms, the neck and superficial refinement. The 1.0mm to 1.5mm diameters in 5cm to 12cm are for facial and submental contouring. A beveled edge is more assertive than a plain one, so treat the superficial layer with corresponding care. Match the fitting to the syringe, vacuum line or handpiece already in your theater.

Why Buy Direct From the Manufacturer

Manufactured by Healermed Instruments, a surgical instruments manufacturer and exporter based in Sialkot, Pakistan. Factory-direct pricing removes the importer and distributor layer. Production runs under an ISO 13485 and FDA CGMP quality system, with ISO 9001 and CE Mark certification. OEM manufacturing and custom branding are available for distributor and brand-owner orders.

Trademark notice: All third-party equipment names are the property of their respective owners. Healermed Instruments is not affiliated with, endorsed by, or sponsored by any third-party equipment manufacturer. This cannula is independently manufactured and the compatibility reference is provided for the buyer's guidance only.

Choose Your Fitting

Every fitting below carries the same beveled hole on top shaft, the same closed blunt tip and the same size grid. Pick the one that matches the syringe, vacuum line or handpiece already in your theater.

More Liposuction Cannulas and Accessories

Healermed manufactures the full range of cannulas for liposuction, from single hole finishing cannulas to high-flow debulking patterns, in 84 diameter and length combinations.

Frequently Asked Questions

What is a beveled hole on top liposuction cannula used for?

It is used to remove subcutaneous fat under vacuum during liposuction and body contouring. The beveled opening leads tissue into the aperture as the cannula advances rather than meeting it square, which keeps the instrument moving smoothly through fibrous tissue, and facing it upward puts the removal in the layer the surgeon can see and feel.

What is the difference between a beveled hole and a square-cut hole cannula?

A square-cut opening meets tissue at ninety degrees, so fibrous strands catch on the edge until vacuum pulls them through. A beveled opening is cut at an angle and leads tissue in progressively, so the cannula moves more smoothly through dense tissue and needs less force to keep going.

Is this cannula autoclavable?

Yes. The instrument is fully reusable and can be steam autoclaved at 134°C. Flush the lumen and the opening with clean water immediately after use, remove all residue before sterilization, and dry completely. Inspect the opening edge under light at every cycle, since edge condition decides how the cannula behaves in tissue.

Which size should I use?

For body contouring of the abdomen, flanks and thighs, 3.0mm to 4.0mm diameters in 25cm to 35cm are the usual range. Arms, neck and superficial refinement suit 2.0mm to 2.5mm in 15cm to 25cm. Facial and submental contouring uses 1.0mm to 1.5mm in 5cm to 12cm.

What is the minimum order quantity for bulk orders?

The minimum order quantity is agreed per order rather than set at a fixed number. Send us the sizes, fittings and quantities you need through the wholesale request page and we will confirm the minimum for that specification. This lets a small distributor start with a trial order and a larger importer scale up on the same terms.

Do you provide samples?

Yes. Samples are available on request and the buyer covers the shipping charges. Send us your machine details with the diameter and length you want to evaluate. Testing a sample in your own handpiece before a bulk order is strongly recommended for any machine-mounted fitting.

Can I order a custom size?

Yes. Custom diameters, working lengths and opening dimensions are available on request in addition to the standard size grid. Send your specification through the wholesale request page and our production team will confirm what can be produced. Custom branding is also available for distributor and OEM orders.