Cobra Round Tip Cannula Toomey Hub 60cc

The Cobra Style Round Tip Liposuction Cannula with Toomey Hub is an aspiration cannula with a fully domed, closed tip, built to fit 60cc Toomey-tip syringes for syringe-assisted liposuction and fat harvesting. The wide, non-Luer Toomey opening lets aspirated fat move without the resistance a narrow taper creates. This fitting is made from 2.0mm (14G) upward. It is listed under Cobra Style Round Tip Liposuction Cannulas, part of the Healermed Liposuction Cannulas and Accessories range.

Buyers also search for this instrument as a 60cc Toomey round tip cannula, a syringe liposuction cannula, or a fat harvesting cannula.

Toomey Hub Round Tip Cannula for 60cc Syringes

A Toomey tip is a wide-bore syringe fitting, not a Luer taper. It exists because aspirated fat is thick and moves slowly through a narrow connector. Combined with a domed tip, it suits fat harvesting particularly well: the connector never clogs, and the atraumatic nose keeps the donor plane intact while the fat is drawn.

What the Round Tip Does

The round tip is a fully domed, closed end with no taper and no edge anywhere on it. That single detail decides how the cannula behaves at the moment of contact: it cannot catch, it cannot start a cut, and it cannot be led off the plane by a firm structure. It pushes tissue aside and lets the surgeon's line of travel decide the direction, rather than the tissue deciding it.

Compare it with a bullet tip. A bullet profile tapers to a narrower nose, which makes it easier to drive through scar and fibrous septa, at the cost of some of that forgiveness. A round tip needs a little more push in dense tissue, and gives back a far lower chance of a septum being divided or the tip skipping into a plane the surgeon did not choose.

That trade favours the round tip wherever the margin for error is smallest. In the superficial layer the skin is close and an irregularity is permanent. Over bony landmarks and near a neurovascular bundle the cost of a tip that catches is not a contour problem. In those places the surgeon wants the most forgiving nose available, and accepts the extra push.

Vacuum works through the side ports, not the end of the shaft. Because the tip itself is sealed, suction never pulls tissue against the leading point, which is what keeps a round-tip cannula from grabbing as it enters.

Key Features

• ✔ Toomey hub matched to standard 60cc Toomey-tip syringes
• ✔ Wide bore keeps aspirated fat moving without clogging at the connector
• ✔ Fully domed round tip with no taper and no edge — the most forgiving profile in the range
• ✔ Sealed tip so suction never pulls tissue against the leading point
• ✔ Blunt dissection through the plane, pushing vessels and nerves aside
• ✔ Deburred port edges for clean passage through fat
• ✔ One-piece German stainless steel shaft, fully reusable
• ✔ Custom diameters, lengths and port configurations available on request

Specifications

Clinical Applications

• Syringe-assisted liposuction of the abdomen, flanks and thighs
• Fat harvesting for grafting, where the donor plane must stay intact
• Arm, neck and submental contouring with the shorter lengths
• Superficial refinement using syringe vacuum

Material and Sterilization

The cannula is made from German stainless steel with a passivated surface that resists corrosion and pitting through repeated cleaning cycles. It is reusable and can be steam autoclaved at 134°C. Flush the lumen and every port with clean water immediately after use and dry fully before autoclaving. Inspect the tip dome at each cycle: the round profile only works while it is smooth, and a dent or flat spot from a dropped instrument turns a forgiving tip into one that catches.

How to Choose

The Toomey fitting starts at 2.0mm, so for finer facial work below 2.0mm choose the Luer lock version instead. Within the Toomey range, 2.0mm to 2.5mm in 15cm to 25cm suits arms, neck and refinement, while 3.0mm to 4.0mm in 25cm to 35cm suits general body contouring.

Why Buy Direct From the Manufacturer

Manufactured by Healermed Instruments, a surgical instruments manufacturer and exporter based in Sialkot, Pakistan. Factory-direct pricing removes the importer and distributor layer. Production runs under an ISO 13485 and FDA CGMP quality system, with ISO 9001 and CE Mark certification. OEM manufacturing and custom branding are available for distributor and brand-owner orders.

Related Instruments

Other fittings in the same cannula range:

• Cobra Style Round Tip Liposuction Cannula – Luer Lock
• Cobra Style Round Tip Liposuction Cannula – Super Luer Lock
• Cobra Style Round Tip Liposuction Cannula – MicroAire PAL Compatible
• Cobra Style Round Tip Liposuction Cannula – main product page
• Cobra Style Round Tip Liposuction Cannulas – all fittings

Frequently Asked Questions

What is a Toomey hub round tip cannula used for?

It is used with 60cc Toomey-tip syringes for syringe-assisted liposuction and fat harvesting. The wide non-Luer hub keeps aspirated fat moving instead of clogging at a narrow connector, while the domed tip keeps the donor plane intact as the cannula passes.

What is the difference between a round tip and a bullet tip cannula?

A round tip is fully domed with no taper; a bullet tip narrows to a nose. The round tip is more forgiving, since it pushes tissue aside rather than parting it, and is preferred in superficial and delicate planes. The bullet tip passes through scar and fibrous tissue with less force, which suits revision and dense areas.

Is this cannula autoclavable?

Yes. The instrument is fully reusable and can be steam autoclaved at 134°C. Flush the lumen and every port with clean water immediately after use, remove all residue before sterilization, and dry completely. Check the tip dome and port edges each cycle, since both affect how the cannula behaves in tissue.

What is the minimum order quantity for bulk orders?

The minimum order quantity is agreed per order rather than set at a fixed number. Send us the sizes, fittings and quantities you need through the wholesale request page and we will confirm the minimum for that specification. This lets a small distributor start with a trial order and a larger importer scale up on the same terms.

Do you provide samples?

Yes. Samples are available on request and the buyer covers the shipping charges. Tell us the diameter and length you want to evaluate and we will confirm what can be sent. Testing a sample first confirms the hub seats correctly on the 60cc syringes you already stock.

Can I order a custom size?

Yes. Custom diameters, working lengths and port configurations are available on request in addition to the standard size grid. Send your specification through the wholesale request page and our production team will confirm what can be produced. Custom branding is also available for distributor and OEM orders.