Nano Fat Transfer Set – Short Pattern

Liposuction Cannulas and Accessories › Nano Fat Transfer Set – Short Pattern

The Nano Fat Transfer Set – Short Pattern is a reusable stainless steel set for emulsifying harvested fat into nanofat, for injection into the dermal and subdermal planes. It is supplied complete with three mesh filters for nano transfer — 0.3mm, 0.5mm and 0.7mm — and two gas rings. It is part of the Healermed liposuction cannulas and accessories range.

Nano Fat Transfer Set – Short Pattern in German Stainless Steel

The short pattern has a compact body, so the channel the fat passes through is shorter than on the long version.

Less channel means less resistance. The plunger moves with noticeably less force, which matters when the preparation is done by hand over many passes and when the volume is small enough that pass count was never the constraint. For a few millilitres of periorbital or perioral nanofat, the short pattern reaches the same emulsion without the effort.

The compact body is also easier to handle on a crowded table and simpler to dismantle and clean, since there is less internal channel for emulsified fat to sit in.

Where the harvest is large, the long pattern will get there in fewer passes. For small and moderate volumes the short pattern is the more comfortable instrument.

How Nano Fat Transfer Works

Nanofat is not a different tissue from the fat that was harvested. It is the same aspirate put through a mechanical process that breaks the fat parcels down until what remains will pass through a very fine cannula.

The process is emulsification by shear. Harvested fat is loaded into a syringe, connected to a second syringe through the transfer device, and pushed back and forth. Each pass forces the tissue through a narrow channel, and the mechanical shear breaks the parcels progressively smaller. After enough passes the aspirate changes visibly, from a lumpy yellow graft to a smooth emulsion.

Filtration then sets what actually gets injected. The emulsified fat is passed through a mesh, and the mesh size decides the largest particle that can get through. That matters because the injection cannula is the real limit: a particle wider than the lumen blocks it, and a blocked fine cannula in the middle of a periorbital case is a problem. Filtering to a known size means the surgeon knows what will pass.

The point of all of it is where the graft can go. Standard fat parcels are too large for the dermal and subdermal planes; nanofat passes through cannulas fine enough to treat them, which is why it is used for skin quality, fine lines, scars, and the thin tissue around the eyes and mouth where conventional grafting cannot be placed.

What Is Included

Each set is supplied complete and ready to use:

Replacement mesh filters and gas rings are available separately.

Key Features

• ✔ Compact body, noticeably less resistance on every pass
• ✔ Suits small and moderate volumes where pass count is not the constraint
• ✔ Less internal channel to dismantle and clean
• ✔ Supplied with three mesh filters and two gas rings
• ✔ Three filtration grades so particle size can be matched to the injection cannula
• ✔ Luer lock at both ends for standard grafting syringes
• ✔ Fully reusable German stainless steel, autoclavable to 134°C
• ✔ Replacement mesh filters and gas rings available separately

Specifications

Clinical Applications

• Preparing small nanofat volumes for periorbital and perioral treatment
• Scar and fine line treatment where only a few millilitres are needed
• Clinics preparing nanofat by hand across many passes

Material and Sterilization

The transfer set is made from German stainless steel and is fully reusable, steam autoclavable to 134°C. Dismantle it completely after every case and flush each part before any residue sets, since emulsified fat dries into the mesh and the internal channel far faster than whole parcels do. Hold each mesh filter to the light and check it is clear across its whole area: a partly blocked mesh raises the pressure the surgeon works against and quietly changes the particle size that gets through. Inspect the gas rings for compression or splitting at every cycle and replace rather than reuse a ring that has flattened.

Why Buy Direct From the Manufacturer

Manufactured by Healermed Instruments, a surgical instruments manufacturer and exporter based in Sialkot, Pakistan. Factory-direct pricing removes the importer and distributor layer. Production runs under an ISO 13485 and FDA CGMP quality system, with ISO 9001 and CE Mark certification. OEM manufacturing and custom branding are available for distributor and brand-owner orders.

The Other Pattern

Frequently Asked Questions

What is a nano fat transfer set used for?

It is used to emulsify harvested fat into nanofat. Fat is driven back and forth between two syringes through the set, and the mechanical shear breaks the parcels down until they pass through a very fine injection cannula. The result is used in the dermal and subdermal planes, where standard fat parcels are too large to place.

What is included with the set?

Three mesh filters for nano transfer — 0.3mm, 0.5mm and 0.7mm — and two gas rings. The three mesh grades let the surgeon match particle size to the injection cannula and the plane being treated. Replacement filters and rings are available separately.

Which mesh size should I use?

Match it to the injection cannula and the plane. The 0.7mm mesh suits subdermal placement through finer cannulas, 0.5mm is the general nanofat grade, and 0.3mm gives the finest emulsion for intradermal work and the thinnest periorbital tissue. A particle wider than the cannula lumen will block it, so filtering to a known size is what keeps the injection running.

When should I choose the short pattern over the long?

Choose the short pattern for small and moderate volumes. The shorter channel means much less force per pass and less internal channel to clean. For large harvests the long pattern reaches the same emulsion in fewer passes, which saves preparation time.

Is the set autoclavable?

Yes. It is fully reusable and steam autoclavable to 134°C. Dismantle it completely after every case and flush each part before residue sets, since emulsified fat dries into the mesh far faster than whole parcels do.

What is the minimum order quantity for bulk orders?

The minimum order quantity is agreed per order rather than set at a fixed number. Send us the patterns and quantities you need through the wholesale request page and we will confirm the minimum for that specification.