Tapered Tip Two Spiral Holes Liposuction Cannula – Luer Lock

Liposuction Cannulas and Accessories › Tapered Tip Two Spiral Holes Liposuction Cannulas › Tapered Tip Two Spiral Holes Liposuction Cannula – Luer Lock

The Tapered Tip Two Spiral Holes Liposuction Cannula with Luer Lock fitting is a tapered tip two spiral holes liposuction cannula is an aspiration cannula with a narrowing closed nose and two openings stepped along the shaft and rotated, used to remove subcutaneous fat under vacuum during liposuction and body contouring. The taper eases entry into fibrous and scarred tissue, and the spiral holes blend the result across passes. It is listed under Tapered Tip Two Spiral Holes Liposuction Cannulas, part of the Healermed Liposuction Cannulas and Accessories range.

Surgeons also refer to these instruments as tapered spiral cannulas, two hole spiral lipo cannulas, revision blending cannulas, or bullet tip spiral aspiration cannulas.

Tapered Tip Two Spiral Holes Liposuction Cannula — Luer Lock

The Luer lock is the most common connection in aesthetic surgery. A threaded collar screws onto the syringe or tubing set and holds the joint closed under vacuum, where a slip fit can pull apart. In syringe-assisted liposuction that matters, because a disconnection breaks the vacuum and interrupts the pass.

How the Tapered Tip and Two Spiral Holes Work Together

Two holes, stepped along the shaft and rotated so they face different sides, behind a tapered closed nose. Each feature answers a different problem, and together they cover the awkward middle of a revision case.

The taper handles entry. A narrowing nose parts fibrous tissue and scar with less force than a domed tip, so the cannula advances where a blunt instrument would stall. Without that, difficult tissue simply cannot be reached in a controlled way.

The spiral placement of the two holes handles what happens after entry. Because the openings sit at different points and face different sides, one pass draws from two depths rather than one line, so the tunnel it leaves is wider and softer edged than two holes set in a row. Adjacent passes overlap instead of sitting beside each other, which is what keeps the result even in tissue that already has irregularity in it from a previous operation.

Two openings rather than three or six keeps the removal rate low enough for corrective work. This is the pattern for reaching a scarred area, taking a modest amount, and blending it into what is around it. The tapered tip is still closed: it parts tissue rather than cutting it, and is more assertive than a domed nose, so it warrants care near the skin.

Key Features

• ✔ Threaded Luer lock hub fits standard Luer lock syringes and suction tubing
• ✔ Tapered closed nose parts fibrous and scarred tissue with less force
• ✔ Two holes set in a spiral draw from two depths, so passes blend instead of stacking
• ✔ Low removal rate suited to corrective rather than bulk work
• ✔ Deburred hole edges for clean passage through fat
• ✔ One-piece German stainless steel shaft, fully reusable
• ✔ Custom diameters, lengths and hole placement available on request

Specifications

Clinical Applications

• Secondary and revision liposuction in tissue that is already uneven
• Blending a corrected area into surrounding tissue
• Fibrous zones where a domed tip stalls or skips out of the plane
• Arm, neck and submental work with the 2.0mm to 2.5mm diameters

Material and Sterilization

The cannula is made from German stainless steel with a passivated surface that resists corrosion and pitting through repeated cleaning cycles. It is reusable and can be steam autoclaved at 134°C. Flush the lumen and the opening with clean water immediately after use and dry fully before autoclaving. The two openings sit at different points along the shaft, so turn the cannula while flushing to be sure water passes through both; check the taper as well, since a dented nose loses the entry advantage the pattern is built around.

How to Choose

Diameter sets how much fat comes out per pass and length sets the reach. This is a corrective pattern, so the 2.0mm to 3.0mm diameters in 15cm to 30cm cover most of its use. The 3.0mm to 4.0mm range in 25cm to 35cm suits larger revision areas. The 1.0mm to 1.5mm diameters in 5cm to 12cm are for facial and submental work. A tapered tip is more assertive than a domed one, so treat the superficial layer with corresponding care. Match the fitting to the syringe, vacuum line or handpiece already in your theater.

Why Buy Direct From the Manufacturer

Manufactured by Healermed Instruments, a surgical instruments manufacturer and exporter based in Sialkot, Pakistan. Factory-direct pricing removes the importer and distributor layer. Production runs under an ISO 13485 and FDA CGMP quality system, with ISO 9001 and CE Mark certification. OEM manufacturing and custom branding are available for distributor and brand-owner orders.

Choose Your Fitting

Every fitting below carries the same tapered tip two spiral holes shaft, the same closed blunt tip and the same size grid. Pick the one that matches the syringe, vacuum line or handpiece already in your theater.

More Liposuction Cannulas and Accessories

Healermed manufactures the full range of cannulas for liposuction, from single hole finishing cannulas to high-flow debulking patterns, in 84 diameter and length combinations.

Frequently Asked Questions

What is a tapered tip two spiral holes liposuction cannula used for?

It is used to remove subcutaneous fat under vacuum in fibrous and previously operated tissue. The tapered closed nose parts scar with less force than a domed tip, while two spiral-set openings draw from two depths so a corrected area blends into the tissue around it instead of leaving a new edge.

What is the difference between two spiral holes and two holes in line?

Two holes in line sit on the same side and draw from one plane; two spiral holes sit at different points along the shaft and face different sides, so a pass draws from two depths. The in-line pattern gives directional aim; the spiral pattern blends better between passes, which matters in tissue that is already uneven.

Is this cannula autoclavable?

Yes. The instrument is fully reusable and can be steam autoclaved at 134°C. Flush the lumen and the opening with clean water immediately after use, remove all residue before sterilization, and dry completely. Inspect the opening edge under light at every cycle, since edge condition decides how the cannula behaves in tissue.

Which size should I use?

The 2.0mm to 3.0mm diameters in 15cm to 30cm cover most corrective work with this pattern. Use 3.0mm to 4.0mm in 25cm to 35cm for larger revision areas, and 1.0mm to 1.5mm in 5cm to 12cm for facial and submental work.

What is the minimum order quantity for bulk orders?

The minimum order quantity is agreed per order rather than set at a fixed number. Send us the sizes, fittings and quantities you need through the wholesale request page and we will confirm the minimum for that specification. This lets a small distributor start with a trial order and a larger importer scale up on the same terms.

Do you provide samples?

Yes. Samples are available on request and the buyer covers the shipping charges. Tell us the diameter and length you want to evaluate and we will confirm what can be sent. Testing a sample first is the fastest way to check edge finish and hub fit against your own syringes.

Can I order a custom size?

Yes. Custom diameters, working lengths and opening dimensions are available on request in addition to the standard size grid. Send your specification through the wholesale request page and our production team will confirm what can be produced. Custom branding is also available for distributor and OEM orders.